Technical drawing, P8 panel cutter D160 – above the workpiece (R)
Panel raising shaper cutter, profile P8, D160–D200 mm, DS Steel, HSS M2 and HW (K40) options
Technical drawing, P8 panel cutter D160 – below the workpiece (L)
Technical drawing, P8 panel cutter D200 – above the workpiece (R)
Technical drawing, P8 panel cutter D200 – below the workpiece (L)
Technical drawing, P8 panel cutter D160 – above the workpiece (R)
Panel raising shaper cutter, profile P8, D160–D200 mm, DS Steel, HSS M2 and HW (K40) options
Technical drawing, P8 panel cutter D160 – below the workpiece (L)
Technical drawing, P8 panel cutter D200 – above the workpiece (R)
Technical drawing, P8 panel cutter D200 – below the workpiece (L)

Note: actual product colours may vary slightly from the images, depending on monitor settings and photo lighting.

SolGrat

Panel Raising Shaper Cutter D160 – D200 | Profile Code P8 | DS, HSS or HW (K40)

SKU: SG-T160P8RDS
€66,95 incl. VAT
Only 1 left
Limited stock
Working Position
Material x Diameter (D) x Bore (d)
Free technical advice

Not sure which tool or accessory you need? Send us a photo, a sketch or your machine model – we'll help you choose.

Free delivery in Romania over 600 lei
100% secure payments
Professional quality

Got questions?

We're here to help

Ask a specialist!

Email +40 756 733 343

Panel Raising Shaper Cutter – DS Steel, HSS M2 or HW (K40) | D160 / D200 | Profile Code P8

Profiled shaper cutter with bore for producing raised panels on a stationary spindle moulder, available in two diameters (160 mm and 200 mm), three material options (DS Steel, HSS M2 or HW (K40) – tungsten carbide) and two working positions (above or below the workpiece) – all selectable from the menu. Commonly used for producing solid wood doors, panelled furniture and decorative wood elements.

Profile CodeProfile CodeP8
Outer Diameter (D)Outer Diameter (D)160 mm or 200 mm – select from the menu
Active Cutting HeightCutting HeightAccording to the technical drawing of the selected variant
Working PositionWorking PositionAbove the workpiece – the cutter cuts from below, upwards | Below the workpiece – the cutter cuts from above, downwards
Bore (d)Bore (d)Ø30 mm standard (HSS / HW) | Ø32 mm (DS variant) – supplied without bushing; 32/30 reduction bushing sold separately | other bore sizes on pre-order
Cutting Edge MaterialCutting Edge MaterialDS Steel – standard woodworking steel | HSS M2 – 4 brazed tips | HW (K40) – 4 brazed tungsten carbide (hard metal) tips, grade K40 (VK15 – 85% WC, 15% Co); a good balance of hardness and toughness, resistant to impact in knots and hardwood
Cutting Edge HardnessHardnessDS Steel – 58–61 HRC | HSS M2 – 63–65 HRC | HW (K40) – 86–87 HRA (VK15)
Recommended SpeedRecommended Speed6,000 RPM
Estimated Tool LifeTool LifeUp to 3,000 linear metres (in softwood, before first resharpening)
Cutting TipsCutting TipsBrazed, can be resharpened repeatedly at a specialised service centre; at advanced wear, the cutter body can be re-tipped
Package ContentsPackage Contents1 x Cutter (variant selected from the menu)
Country of OriginCountry of OriginUkraine

🚀 PROPERTIES AND PERFORMANCE:

  • Robust, Balanced Body: made of heat-treated steel, the cutter body minimises vibration, protecting the machine bearings and ensuring flat finishes.
  • Fine, Precise Cut: whichever material you choose, the brazed tips deliver a consistent cut and a finish straight off the cutter, ready for staining or lacquering.
  • Z4 Configuration: the 4 tips distribute the cutting load evenly, without tear-out.
  • 3 Investment Levels: DS Steel for low cost on softwood, HSS M2 for a performance–price balance, HW (K40) for industrial volume, hardwood and abrasive materials.
  • Long-Term Investment: the tips can be resharpened repeatedly at a specialised service centre, and at advanced wear the cutter body can be re-tipped.
  • Maximum Flexibility: 2 diameters × 3 materials × 2 working positions — select the exact combination for your machine and project.

💡 HOW TO CHOOSE THE WORKING POSITION:

– Above the workpiece – you can check the profile visually while cutting; recommended for manual work with feed controlled from above.
– Below the workpiece – shavings and chips are thrown straight down; the finished face stays protected while it slides on the moulder table.

⚠️ USAGE LIMITATIONS:

  • DS Steel variant: ❌ NOT recommended for particleboard, MDF, HDF or hard/exotic wood – intended for softwood only (conifers, lime).
  • HSS M2 variant: ❌ not recommended for particleboard, MDF, HDF or very hard exotic wood – synthetic binders wear the high-speed steel edge prematurely.
  • HW (K40) variant on softwood: requires a constant feed rate – letting the cutter dwell in resinous species can cause local burning.

🛠️ SELECTION GUIDE: DS STEEL vs. HSS M2 vs. HW (K40)

The cutting material directly affects finish quality, cost and tool life (swipe left-right on mobile to see the full table):

Workpiece Material DS Steel
(Economical)		 HSS M2
(6% W · 5% Mo)		 HW (K40) ⭐
(Tungsten carbide)
Softwood
(Fir, Spruce, Pine)		 90%
(Good / Economical)		 ⭐ 100%
(No Burning)		 ⚠️ Burning risk
(Constant feed required)
Hardwood
(Beech, Oak, Ash)		 40%
(Fast dulling)		 80%
(Efficient)		 ⭐ 100%
(Wear-resistant)
MDF / Particleboard / HDF / Laminated board Not recommended Not recommended ⭐ 100%
(Optimal)
Edge Hardness 58 – 61 HRC 63 – 65 HRC 86 – 87 HRA
💡 Buying recommendations:
  1. Tight budget, softwood only? Choose DS Steel – the lowest cost for fir, spruce or pine.
  2. Working fir, spruce or pine in medium volume? Choose HSS M2 – clean white finish, no burn marks, more durable than DS.
  3. Working oak, beech, MDF or particleboard? Choose HW (K40) – withstands the abrasive wear of hardwoods and synthetic binders.

🦺 SAFETY MEASURES:

  • Mandatory protective equipment: safety glasses (against flying chips), a respirator mask or filter (fine wood dust) and hearing protection for extended work.
  • Keep hands and fingers clear: always use a push stick or power feeder; never guide the workpiece by hand close to the cutter.
  • Check the cutter orientation before starting the machine – the “Above” and “Below” variants are not interchangeable; incorrect mounting produces a wrong profile.
  • Check the mounting of the cutter on the spindle and that the nut is fully tightened before starting.
  • Observe the recommended speed of 6,000 RPM.

Delivery in 24–48 working hours for in-stock products, by courier (Fan Courier, Sameday, Cargus, DPD, GLS).

“On order” products (for example a variant with a different bore, such as Ø30 or Ø35, or a product not currently in stock): delivery time is 1–4 weeks. Place your order on the site as usual. Right after, an agent will call you to confirm the exact date, then the product is shipped to you by courier.

Free delivery in Romania for orders over 600 lei. We also ship to the EU, Moldova and Ukraine – the cost is calculated at checkout. Details in our Shipping policy.

This product is covered by the legal guarantee of conformity of at least 2 years, under EU and Romanian law. If the product does not match its description or does not work as intended, you are entitled to free repair or replacement and, in some cases, a price reduction or refund.

See the EU notice on the legal guarantee · europa.eu/youreurope – guarantees

Customer Reviews

Based on 1 review
100%
(1)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
M
Marin Constantin
Am pus Freza la treabă 💪🏻

Sunt mulțumit 🤝

Marin Constantin review photo

Order several variants

Variant Quantity Price Total
Technical drawing, P8 panel cutter D160 – above the workpiece (R)
Above / DS x D160 x d32 SG-T160P8RDS
€66,95 incl. VAT
€0,00
€66,95 incl. VAT
€0,00
Technical drawing, P8 panel cutter D160 – above the workpiece (R)
Above / HSS M2 x D160 x d30 SG-T160P8RHSS
€107,95 incl. VAT
€0,00
Out of stock
€107,95 incl. VAT
€0,00
Technical drawing, P8 panel cutter D160 – above the workpiece (R)
Above / HW (K40) x D160 x d30 SG-T160P8RHW
€154,95 incl. VAT
€0,00
€154,95 incl. VAT
€0,00
Technical drawing, P8 panel cutter D200 – above the workpiece (R)
Above / DS x D200 x d32 SG-T200P8RDS
€85,95 incl. VAT
€0,00
€85,95 incl. VAT
€0,00
Technical drawing, P8 panel cutter D200 – above the workpiece (R)
Above / HSS M2 x D200 x d30 SG-T200P8RHSS
€127,95 incl. VAT
€0,00
€127,95 incl. VAT
€0,00
Technical drawing, P8 panel cutter D200 – above the workpiece (R)
Above / HW (K40) x D200 x d30 SG-T200P8RHW
€170,95 incl. VAT
€0,00
€170,95 incl. VAT
€0,00
Technical drawing, P8 panel cutter D160 – below the workpiece (L)
Below / DS x D160 x d32 SG-T160P8LDS
€66,95 incl. VAT
€0,00
Out of stock
€66,95 incl. VAT
€0,00
Technical drawing, P8 panel cutter D160 – below the workpiece (L)
Below / HSS M2 x D160 x d30 SG-T160P8LHSS
€107,95 incl. VAT
€0,00
Out of stock
€107,95 incl. VAT
€0,00
Technical drawing, P8 panel cutter D160 – below the workpiece (L)
Below / HW (K40) x D160 x d30 SG-T160P8LHW
€154,95 incl. VAT
€0,00
€154,95 incl. VAT
€0,00
Technical drawing, P8 panel cutter D200 – below the workpiece (L)
Below / DS x D200 x d32 SG-T200P8LDS
€85,95 incl. VAT
€0,00
€85,95 incl. VAT
€0,00
Technical drawing, P8 panel cutter D200 – below the workpiece (L)
Below / HSS M2 x D200 x d30 SG-T200P8LHSS
€127,95 incl. VAT
€0,00
€127,95 incl. VAT
€0,00
Technical drawing, P8 panel cutter D200 – below the workpiece (L)
Below / HW (K40) x D200 x d30 SG-T200P8LHW
€170,95 incl. VAT
€0,00
Out of stock
€170,95 incl. VAT
€0,00
View cart
0 Total items
€0,00

Product subtotal