Desen tehnic freză tăblie N13 D160 – poziție deasupra lemnului (R)
Freză pentru tăblie lemn profil N13, D160–D200 mm, variante DS Steel, HSS M2 și HW (K40)
Desen tehnic freză tăblie N13 D160 – poziție sub lemn (L)
Desen tehnic freză tăblie N13 D160 – poziție deasupra lemnului (R)
Freză pentru tăblie lemn profil N13, D160–D200 mm, variante DS Steel, HSS M2 și HW (K40)
Desen tehnic freză tăblie N13 D160 – poziție sub lemn (L)

Note: actual product colours may vary slightly from the images, depending on monitor settings and photo lighting.

SolGrat

Panel Raising Shaper Cutter D160 – D200 | Profile Code P13 | DS, HSS or HW (K40)

SKU: FT160P13RDS
€82,95 incl. VAT
Only 1 left
Limited stock
Working Position
Material x Diameter (D) x Bore (d)
Free technical advice

Not sure which tool or accessory you need? Send us a photo, a sketch or your machine model – we'll help you choose.

Free delivery in Romania over 600 lei
100% secure payments
Professional quality

Got questions?

We're here to help

Ask a specialist!

Email +40 756 733 343

Panel Raising Shaper Cutter – DS Steel, HSS M2 or HW (K40) | D160 / D200 | Profile Code P13

Profiled shaper cutter with bore for producing raised panels on a stationary spindle moulder, available in two diameters (160 mm and 200 mm), three material options (DS Steel, HSS M2 or HW (K40) – tungsten carbide) and two working positions (above or below the workpiece) – all selectable from the menu. Commonly used for producing solid wood doors, panelled furniture and decorative wood elements.

Profile CodeProfile CodeP13
Outer Diameter (D)Outer Diameter (D)160 mm or 200 mm – select from the menu
Active Cutting HeightCutting Height16 mm (D160) – according to the technical drawing of the selected variant
Working PositionWorking PositionAbove the workpiece – the cutter cuts from below, upwards | Below the workpiece – the cutter cuts from above, downwards
Bore (d)Bore (d)Ø30 mm standard (HSS / HW) | Ø32 mm (DS variant) – supplied without bushing; 32/30 reduction bushing sold separately | other bore sizes on pre-order
Cutting Edge MaterialCutting Edge MaterialDS Steel – standard woodworking steel | HSS M2 – 4 brazed tips | HW (K40) – 4 brazed tungsten carbide (hard metal) tips, grade K40 (VK15 – 85% WC, 15% Co); a good balance of hardness and toughness, wear-resistant in hardwood and abrasive materials
Cutting Edge HardnessHardnessDS Steel – 58–61 HRC | HSS M2 – 63–65 HRC | HW (K40) – 86–87 HRA (VK15)
Recommended SpeedRecommended Speed6,000 RPM
Estimated Tool LifeTool LifeUp to 3,000 linear metres (in softwood, before first resharpening)
Cutting TipsCutting TipsBrazed, can be resharpened repeatedly at a specialised service centre; at advanced wear, the cutter body can be re-tipped
Package ContentsPackage Contents1 x Cutter (variant selected from the menu)
Country of OriginCountry of OriginUkraine

🚀 PROPERTIES AND PERFORMANCE:

  • Robust, Balanced Body: made of heat-treated steel, the cutter body minimises vibration, protecting the machine bearings and ensuring flat finishes.
  • Fine, Precise Cut: whichever material you choose, the brazed tips deliver a consistent cut and a finish straight off the cutter, ready for staining or lacquering.
  • Z4 Configuration: the 4 tips distribute the cutting load evenly, without tear-out.
  • 3 Investment Levels: DS Steel for low cost on softwood, HSS M2 for a performance–price balance, HW (K40) for industrial volume, hardwood and abrasive materials.
  • Long-Term Investment: the tips can be resharpened repeatedly at a specialised service centre, and at advanced wear the cutter body can be re-tipped.
  • Maximum Flexibility: 2 diameters × 3 materials × 2 working positions — select the exact combination for your machine and project.

💡 HOW TO CHOOSE THE WORKING POSITION:

– Above the workpiece – you can check the profile visually while cutting; recommended for manual work with feed controlled from above.
– Below the workpiece – shavings and chips are thrown straight down; the finished face stays protected while it slides on the moulder table.

⚠️ USAGE LIMITATIONS:

  • DS Steel variant: ❌ NOT recommended for particleboard, MDF, HDF or hard/exotic wood – intended for softwood only (conifers, lime).
  • HSS M2 variant: ❌ not recommended for particleboard, MDF, HDF or very hard exotic wood – synthetic binders wear the high-speed steel edge prematurely.
  • HW (K40) version: carbide is harder but more brittle than HSS – hard knots or foreign bodies (nails, sand) can chip the edge. Keep a constant feed; do not let the cutter spin in place in the wood.

🛠️ SELECTION GUIDE: DS STEEL vs. HSS M2 vs. HW (K40)

The cutting material directly affects finish quality, cost and tool life (swipe left-right on mobile to see the full table):

Workpiece Material DS Steel
(Economical)		 HSS M2
(6% W · 5% Mo)		 HW (K40) ⭐
(Tungsten carbide)
Softwood
(Fir, Spruce, Pine)		 90%
(Good / Economical)		 ⭐ Optimal
Fine finish · no chipping on knots		 ✔ Recommended for production
4-sided moulders · long runs · clean wood
Hardwood
(Beech, Oak, Ash)		 40%
(Fast dulling)		 80%
(Efficient)		 ⭐ 100%
(Wear-resistant)
MDF / Particleboard / HDF / Laminated board Not recommended Not recommended ⭐ 100%
(Optimal)
Edge Hardness 58 – 61 HRC 63 – 65 HRC 86 – 87 HRA
💡 Buying recommendations:
  1. Tight budget, softwood only? Choose DS Steel – the lowest cost for fir, spruce or pine.
  2. Workshop, small to medium runs, knotty wood? Choose HSS M2 – it does not chip on knots and is easy to sharpen.
  3. Daily production, 4-sided moulder, clean wood or MDF/PAL? Choose HW (K40) – it holds its edge several times longer between sharpenings.

🦺 SAFETY MEASURES:

  • Mandatory protective equipment: safety glasses (against flying chips), a respirator mask or filter (fine wood dust) and hearing protection for extended work.
  • Keep hands and fingers clear: always use a push stick or power feeder; never guide the workpiece by hand close to the cutter.
  • Check the cutter orientation before starting the machine – the “Above” and “Below” variants are not interchangeable; incorrect mounting produces a wrong profile.
  • Check the mounting of the cutter on the spindle and that the nut is fully tightened before starting.
  • Observe the recommended speed of 6,000 RPM.

Delivery in 24–48 working hours for in-stock products, by courier (Fan Courier, Sameday, Cargus, DPD, GLS).

“On order” products (for example a variant with a different bore, such as Ø30 or Ø35, or a product not currently in stock): delivery time is 1–4 weeks. Place your order on the site as usual. Right after, an agent will call you to confirm the exact date, then the product is shipped to you by courier.

Free delivery in Romania for orders over 600 lei. We also ship to the EU, Moldova and Ukraine – the cost is calculated at checkout. Details in our Shipping policy.

This product is covered by the legal guarantee of conformity of at least 2 years, under EU and Romanian law. If the product does not match its description or does not work as intended, you are entitled to free repair or replacement and, in some cases, a price reduction or refund.

See the EU notice on the legal guarantee · europa.eu/youreurope – guarantees

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)

Order several variants

Variant Quantity Price Total
Desen tehnic freză tăblie N13 D160 – poziție deasupra lemnului (R)
Above / DS x D160 x d32 FT160P13RDS
€82,95 incl. VAT
€0,00
€82,95 incl. VAT
€0,00
Desen tehnic freză tăblie N13 D160 – poziție deasupra lemnului (R)
Above / HSS M2 x D160 x d30 FT160P13RHSS
€128,95 incl. VAT
€0,00
Out of stock
€128,95 incl. VAT
€0,00
Desen tehnic freză tăblie N13 D160 – poziție deasupra lemnului (R)
Above / HW (K40) x D160 x d30 FT160P13RHW
€174,95 incl. VAT
€0,00
Out of stock
€174,95 incl. VAT
€0,00
Above / DS x D200 x d32 FT200P13RDS
€112,95 incl. VAT
€0,00
Out of stock
€112,95 incl. VAT
€0,00
Above / HSS M2 x D200 x d30 FT200P13RHSS
€145,95 incl. VAT
€0,00
Out of stock
€145,95 incl. VAT
€0,00
Above / HW (K40) x D200 x d30 FT200P13RHW
€195,95 incl. VAT
€0,00
Out of stock
€195,95 incl. VAT
€0,00
Desen tehnic freză tăblie N13 D160 – poziție sub lemn (L)
Below / DS x D160 x d32 FT160P13LDS
€82,95 incl. VAT
€0,00
€82,95 incl. VAT
€0,00
Desen tehnic freză tăblie N13 D160 – poziție sub lemn (L)
Below / HSS M2 x D160 x d30 FT160P13LHSS
€128,95 incl. VAT
€0,00
Out of stock
€128,95 incl. VAT
€0,00
Desen tehnic freză tăblie N13 D160 – poziție sub lemn (L)
Below / HW (K40) x D160 x d30 FT160P13LHW
€174,95 incl. VAT
€0,00
Out of stock
€174,95 incl. VAT
€0,00
Below / DS x D200 x d32 FT200P13LDS
€112,95 incl. VAT
€0,00
Out of stock
€112,95 incl. VAT
€0,00
Below / HSS M2 x D200 x d30 FT200P13LHSS
€145,95 incl. VAT
€0,00
Out of stock
€145,95 incl. VAT
€0,00
Below / HW (K40) x D200 x d30 FT200P13LHW
€195,95 incl. VAT
€0,00
Out of stock
€195,95 incl. VAT
€0,00
View cart
0 Total items
€0,00

Product subtotal