Desen tehnic freză tăblie P7 D160 – poziție deasupra lemnului (R)

Freză pentru tăblie lemn profil P7, D160–D200 mm, variante DS Steel, HSS M2 și HW (K40)

Desen tehnic freză tăblie P7 D200 – poziție deasupra lemnului (R)

Desen tehnic freză tăblie P7 D160 – poziție sub lemn (L)

Desen tehnic freză tăblie P7 D200 – poziție sub lemn (L)

Note: actual product colours may vary slightly from the images, depending on monitor settings and photo lighting.

SolGrat

Panel Raising Shaper Cutter D160 – D200 | Profile Code P7 | DS, HSS or HW (K40)

SKU: SG-T160P7RDS

€66,95 incl. VAT

Made to order

On order

Working Position

Above Below

Material x Diameter (D) x Bore (d)

DS x D160 x d32 HSS M2 x D160 x d30 HW (K40) x D160 x d30 DS x D200 x d32 HSS M2 x D200 x d30 HW (K40) x D200 x d30

Free technical advice

Not sure which tool or accessory you need? Send us a photo, a sketch or your machine model – we'll help you choose.

Free delivery in Romania over 600 lei

100% secure payments

Professional quality

Got questions?

Panel Raising Shaper Cutter – DS Steel, HSS M2 or HW (K40) | D160 / D200 | Profile Code P7

Profiled shaper cutter with bore for producing raised panels on a stationary spindle moulder. The P7 profile combines a fine step at the edge, a double R20 curve and a long 3° bevel towards the panel edge. Available in two diameters (160 mm and 200 mm), three material options (DS Steel, HSS M2 or HW (K40) – tungsten carbide) and two working positions (above or below the workpiece) – all selectable from the menu. Commonly used for producing solid wood doors, panelled furniture and decorative wood elements.

Profile Code	Profile CodeP7
Outer Diameter (D)	Outer Diameter (D)160 mm or 200 mm – select from the menu
Profile Depth	Profile Depth45 mm (D160) \| 55 mm (D200)
Profile Geometry	Profile GeometryStep + double R20 curve (18 mm wide, 10.7 mm deep) + 3° bevel – see the technical drawing
Working Position	Working PositionAbove the workpiece – the cutter cuts from below, upwards \| Below the workpiece – the cutter cuts from above, downwards
Bore (d)	Bore (d)Ø30 mm (HSS / HW) \| Ø32 mm (DS variant) – supplied without bushing; the 32/30 reduction bushing is sold separately \| other bore sizes on pre-order
Cutting Edge Material	Cutting Edge MaterialDS Steel – standard woodworking steel \| HSS M2 – 4 brazed tips \| HW (K40) – 4 brazed tungsten carbide (hard metal) tips, grade K40 (VK15 – 85% WC, 15% Co); a good balance of hardness and toughness, resistant to impact in knots and hardwood
Cutting Edge Hardness	HardnessDS Steel – 58–61 HRC \| HSS M2 – 63–65 HRC \| HW (K40) – 86–87 HRA (VK15)
Recommended Speed	Recommended Speed6,000 RPM
Estimated Tool Life	Tool LifeUp to 3,000 linear metres (in softwood, before first resharpening)
Cutting Tips	Cutting TipsBrazed, can be resharpened repeatedly at a specialised service centre; at advanced wear, the cutter body can be re-tipped
Package Contents	Package Contents1 x Cutter (variant selected from the menu)
Country of Origin	Country of OriginUkraine

🚀 PROPERTIES AND PERFORMANCE:

Robust, Balanced Body: made of heat-treated steel, the cutter body minimises vibration, protecting the machine bearings and ensuring flat finishes.
Fine, Precise Cut: whichever material you choose, the brazed tips deliver a consistent cut and a finish straight off the cutter, ready for staining or lacquering.
Z4 Configuration: the 4 tips distribute the cutting load evenly, without tear-out.
3 Investment Levels: DS Steel for low cost on softwood, HSS M2 for a performance–price balance, HW (K40) for industrial volume, hardwood and abrasive materials.
Long-Term Investment: the tips can be resharpened repeatedly at a specialised service centre, and at advanced wear the cutter body can be re-tipped.
Maximum Flexibility: 2 diameters × 3 materials × 2 working positions — select the exact combination for your machine and project.

💡 HOW TO CHOOSE THE WORKING POSITION:

– Above the workpiece – you can check the profile visually while cutting; recommended for manual work with feed controlled from above.
– Below the workpiece – shavings and chips are thrown straight down; the finished face stays protected while it slides on the moulder table.

⚠️ USAGE LIMITATIONS:

DS Steel variant: ❌ NOT recommended for particleboard, MDF, HDF or hard/exotic wood – intended for softwood only (conifers, lime).
HSS M2 variant: ❌ not recommended for particleboard, MDF, HDF or very hard exotic wood – synthetic binders wear the high-speed steel edge prematurely.
HW (K40) variant on softwood: requires a constant feed rate – letting the cutter dwell in resinous species can cause local burning.

🛠️ SELECTION GUIDE: DS STEEL vs. HSS M2 vs. HW (K40)

The cutting material directly affects finish quality, cost and tool life (swipe left-right on mobile to see the full table):

Workpiece Material	DS Steel (Economical)	HSS M2 (6% W · 5% Mo)	HW (K40) ⭐ (Tungsten carbide)
Softwood (Fir, Spruce, Pine)	90% (Good / Economical)	⭐ 100% (No Burning)	⚠️ Burning risk (Constant feed required)
Hardwood (Beech, Oak, Ash)	40% (Fast dulling)	80% (Efficient)	⭐ 100% (Wear-resistant)
MDF / Particleboard / HDF / Laminated board	Not recommended	Not recommended	⭐ 100% (Optimal)
Edge Hardness	58 – 61 HRC	63 – 65 HRC	86 – 87 HRA

💡 Buying recommendations:

Tight budget, softwood only? Choose DS Steel – the lowest cost for fir, spruce or pine.
Working fir, spruce or pine in medium volume? Choose HSS M2 – clean white finish, no burn marks, more durable than DS.
Working oak, beech, MDF or particleboard? Choose HW (K40) – withstands the abrasive wear of hardwoods and synthetic binders.

🦺 SAFETY MEASURES:

Mandatory protective equipment: safety glasses (against flying chips), a respirator mask or filter (fine wood dust) and hearing protection for extended work.
Keep hands and fingers clear: always use a push stick or power feeder; never guide the workpiece by hand close to the cutter.
Check the cutter orientation before starting the machine – the “Above” and “Below” variants are not interchangeable; incorrect mounting produces a wrong profile.
Check the mounting of the cutter on the spindle and that the nut is fully tightened before starting.
Observe the recommended speed of 6,000 RPM.

Order several variants

Variant	Quantity	Total
Above / DS x D160 x d32/30 SG-T160P7RDS Regular price €66,95 incl. VAT	€0,00	Regular price €66,95 incl. VAT	€0,00
Above / HSS M2 x D160 x d30 SG-T160P7RHSS Regular price €106,95 incl. VAT	€0,00	Regular price €106,95 incl. VAT	€0,00
Above / HW (K40) x D160 x d30 SG-T160P7RHW Regular price €154,95 incl. VAT	€0,00	Regular price €154,95 incl. VAT	€0,00
Above / DS x D200 x d32/30 SG-T200P7RDS Regular price €85,95 incl. VAT	€0,00	Regular price €85,95 incl. VAT	€0,00
Above / HSS M2 x D200 x d30 SG-T200P7RHSS Regular price €126,95 incl. VAT	€0,00	Regular price €126,95 incl. VAT	€0,00
Above / HW (K40) x D200 x d30 SG-T200P7RHW Regular price €169,95 incl. VAT	€0,00	Regular price €169,95 incl. VAT	€0,00
Below / DS x D160 x d32/30 SG-T160P7LDS Regular price €66,95 incl. VAT	€0,00	Regular price €66,95 incl. VAT	€0,00
Below / HSS M2 x D160 x d30 SG-T160P7LHSS Regular price €106,95 incl. VAT	€0,00	Regular price €106,95 incl. VAT	€0,00
Below / HW (K40) x D160 x d30 SG-T160P7LHW Regular price €154,95 incl. VAT	€0,00	Regular price €154,95 incl. VAT	€0,00
Below / DS x D200 x d32/30 SG-T200P7LDS Regular price €85,95 incl. VAT	€0,00	Regular price €85,95 incl. VAT	€0,00
Below / HSS M2 x D200 x d30 SG-T200P7LHSS Regular price €126,95 incl. VAT	€0,00	Regular price €126,95 incl. VAT	€0,00
Below / HW (K40) x D200 x d30 SG-T200P7LHW Regular price €169,95 incl. VAT	€0,00	Regular price €169,95 incl. VAT	€0,00